Full home automation for android and apple

How to switch a fan using android phone (arduino projects)

Needed=arduino esp8266 shield 12E

2 channel 5v relay module

male to female jumper wire

3.7v battery

Blynk

Connecting method (pin congconfiguration)
arduino 5v::relay vcc Arduino D6::relay pin 1
Arduino D7::relay pin2
Arduino GND::relay GND

Now the time for coding
Blynk esp8266 standalone example coding and change wifi ssid and password.

Then write your auth token
from blynk email correctly.

Then get in your blynk application and then select your pin correctly

What is blynk=blynk is a common app for arduino wifi projects.
Blynk app is support for android , ios , windows operating systems.
blynk app have a online server so its need data connection from your phone or wifi.

What is arduino ide=arduino ide is supported operating systems are windows android ios.
its use for writting coding for all arduino programming boards.

Arduino and other component buyable websites
Www.ebay.com
www.aliexpress.com
www.lankatronics.com
.......
.....
...
.

Comments

Arduino colour sensor and servo pro

Colour sensor with servo project Making All we need for this project is one color sensor (TCS3200) and two hobbyist servo motors, which makes this project quite simple but yet very fun to build it. In the first place, using the Solidworks 3D modeling software I made the design of the color sorter and here’s its working principle Initially, the colored skittles which are held in the charger drop into the platform attached on the top servo motor.Then the servo motor rotates and brings the skittle to the color sensor which detects its color.After that the bottom servo motor rotates to the particular position and then the top servo motor rotates again till the skittle drop into the guide rail. Connecting method The code is below /* Arduino Project - Color Sorting Machine * * by Dejan Nedelkovski, www.HowToMechatronics.com * */ #include <Servo.h> #define S0 2 #define S1 3 #define S2 4 #define S3 5 #define sensorOut 6 Servo topServo; Servo b

how to fire a matchstrick wirelessly using android phone

Copper wire:0.5mm/1mm Copper wire:0.1-0.4mm Motor Arduino esp8266 12E 5v relay module Alkaline battery:5v-9v AA battery:3v Android phone Blynk application No worry about this circuit because this is 100% working and tested. The basic consept of this circuit is below This circuit is possible because mini copper wire get more heat than the bigger wire. Codeing method First you install arduino ide on your pc Then copy and paste this code in your arduino #define BLYNK_PRINT Serial // Comment this out to disable prints and save space #include <ESP8266WiFi.h> #include <BlynkSimpleEsp8266.h> // You should get Auth Token in the Blynk App. // Go to the Project Settings (nut icon). char auth[] = "YourAuthToken"; // Your WiFi credentials. // Set password to "" for open networks. char ssid[] = "YourNetworkName"; char pass[] = "YourPassword"; void setup() { Serial.begi

How to make a poket radio(circuit)

Pocket radio diagram Needed BF 494 transistor T1, T2. Variable resistor. Variable capacitor. Inductor coil. Lm 386 IC Follow this diagram and do it, Then follow the instruction :Initially connect the circuit as shown in the figure. :Connect the power supply to the circuit. :Now press the switch. :Now adjust the frequency of the circuit by varying the trim pot (variable capacitor) of the tank circuit. :Thus the circuit starts tuning to the nearest frequency. :When the frequency of incoming signal is matched sound can be heard through the headphone or speaker. :Now tune the circuit to the another frequency using tank circuit. :You can listen another sound incoming at that particular frequency. :Adjust the variable resistor to increase or decrease the volume. Try and enjoy it

S.Thanush

Search This Blog