Skip to main content

tesla coil

Make a simple Tesla coil
Needed
2N2222 transistor
22k resister
Switch
9V battery
Copper wires (0.5mm)
Copper wires (1mm)

Follow the steps below


Do this circuit and switch the circuit and then get a CFL bulb near the coil now the bulb was switched.

 2N2222 transistor details

  • Silicon material transistor
  • NPN polarity
  • 0.5w maximum collector power dissipation
  • 60v maximum collector base voltage
  • 30v maximum collector emitter voltage
  • 5v maximum emitter base voltage
  • 0.8A maximum collector current
  • 175c maximum operating junction temparature
  • 250mhz transition frequncy
  • 8pf collector capasitance
  • 100 minimum forward current transfer ratio

Comments

Post a Comment

Popular posts from this blog

Arduino colour sensor and servo pro

Colour sensor with servo project Making All we need for this project is one color sensor (TCS3200) and two hobbyist servo motors, which makes this project quite simple but yet very fun to build it. In the first place, using the Solidworks 3D modeling software I made the design of the color sorter and here’s its working principle Initially, the colored skittles which are held in the charger drop into the platform attached on the top servo motor.Then the servo motor rotates and brings the skittle to the color sensor which detects its color.After that the bottom servo motor rotates to the particular position and then the top servo motor rotates again till the skittle drop into the guide rail. Connecting method The code is below /* Arduino Project - Color Sorting Machine * * by Dejan Nedelkovski, www.HowToMechatronics.com * */ #include <Servo.h> #define S0 2 #define S1 3 #define S2 4 #define S3 5 #define sensorOut 6 Servo topServo; Servo b...
1 comment
Read more

220v ac to 5v dc without transformer

220v ac to 5v dc converted circuit Needed 4*1N4007 diode 100 ohm 1W 470k 1W 225k/400v capasitor 470uf/100v capasitor 220ohm resistor 15v 1W diode led 10uf 25v capasitor 7805 ic 1uf 10v Now the time for circuit design This is the simplest way for converting 220 ac volts to 5v dc volts (usb current) it is use for mobile phone charger and power bank charger. Capasitor in this circuit for give smooth current. Diode in this circuit for convert ac to dc. (Diode bridge)   Capasitor in this circuit. Capacitors in DC Circuits. Capacitors do not play an important role in DC circuits because it is impossible for a steady current to flow across acapacitor. If an uncharged capacitor is connected across the terminals of a battery of voltage then a transient current flows as the capacitor plates charge up. Diode in this circuit for. Diodes can be used as rectifiers, signal limiters, voltage regulators, switches, signal modulators, sign...
7 comments
Read more

how to fire a matchstrick wirelessly using android phone

Copper wire:0.5mm/1mm Copper wire:0.1-0.4mm Motor Arduino esp8266 12E 5v relay module Alkaline battery:5v-9v AA battery:3v Android phone Blynk application No worry about this circuit because this is 100% working and tested. The basic consept of this circuit is below This circuit is possible because mini copper wire get more heat than the bigger wire. Codeing method First you install arduino ide on your pc Then copy and paste this code in your arduino #define BLYNK_PRINT Serial    // Comment this out to disable prints and save space #include <ESP8266WiFi.h> #include <BlynkSimpleEsp8266.h> // You should get Auth Token in the Blynk App. // Go to the Project Settings (nut icon). char auth[] = "YourAuthToken"; // Your WiFi credentials. // Set password to "" for open networks. char ssid[] = "YourNetworkName"; char pass[] = "YourPassword"; void setup() {   Serial.begi...
Post a Comment
Read more